Results 1 to 17 of 17
-
03-04-2013, 05:10 AM #1
ESS VT2-625 supercharged DCT E92 M3 versus Paxton supercharged 2013 Mustang 5.0
Yet another great video from the No Fly Zone event (expect a whole lot of race videos to be posted throughout this week). Strong Mustang here running a Paxton 2200SL supercharger through the stock exhaust system with a 6-speed manual transmission. This Mustang is said to be putting down in the ~600 wheel horsepower range and also was able to dispatch a Weistec Stage II supercharged W204 Mercedes-Benz C63 AMG.
The blown Mustang 5.0 also beats this ESS DCT M3 although the M3 does hang in pretty well seemingly getting a small jump likely due to the Mustang starting in a higher gear (3rd gear around 3500 rpm) due to traction issues in second gear. Video is below.
-
03-04-2013, 09:25 AM #2
Member
- Join Date
- Feb 2011
- Posts
- 982
- Rep Points
- 1,552.0
- Mentioned
- 19 Post(s)
- Rep Power
- 16
If that Mustang really throws down ~600whp, then AMAZING work by the ESS VT2-625.
It's amazing what a blower and DCT can really do.
Both insanely fast cars!2002 E46 M3 6MT | Jet Black . Black Nappa | My GermanBoost Build Thread
2009 E90 M3 DCT | Melbourne Red . Speed Cloth
-
03-04-2013, 12:29 PM #3
Member
- Join Date
- Jan 2013
- Posts
- 24
- Rep Points
- 78.1
- Mentioned
- 1 Post(s)
- Rep Power
- 0
I was the Mustang's "victim" in this run...He was running close to 600whp on a 97 octane tune (using Torco). Mustang owner is a close friend so this morning there is a lot of $#@! talking here @ work
.
I was a foot back from his bumper at the half mile mark....
-
03-04-2013, 12:31 PM #4
Member
- Join Date
- Feb 2013
- Posts
- 16
- Rep Points
- 83.6
- Mentioned
- 5 Post(s)
- Rep Power
- 0
In that run I started in 3rd at 3500rpm, so he got a big jump. I ran him again starting at 50mph at 4500rpm and I won by 2+ cars. Either way it was pretty close. DCT sure helps. Cars were getting heatsoaked pretty bad later in the day so power levels were dropping.
-
03-04-2013, 12:38 PM #5
-
03-04-2013, 12:44 PM #6
Member
- Join Date
- Feb 2013
- Posts
- 16
- Rep Points
- 83.6
- Mentioned
- 5 Post(s)
- Rep Power
- 0
Here is my dyno from a week ago from a tuning session at Cunningham Motorsports. This is a Torco map.
Thanks Ryne for a reliable tune
-
03-04-2013, 12:47 PM #7
-
03-04-2013, 12:50 PM #8
Member
- Join Date
- Feb 2013
- Posts
- 16
- Rep Points
- 83.6
- Mentioned
- 5 Post(s)
- Rep Power
- 0
nope, all I got from the tuner. I was making very similar power on a dynojet with SAE correction, so it should be pretty close.
-
03-04-2013, 12:55 PM #9
Member
- Join Date
- Jan 2013
- Posts
- 24
- Rep Points
- 78.1
- Mentioned
- 1 Post(s)
- Rep Power
- 0
*cough* only faster on Torco *cough*
...now I need to get a 100 octane tune & get rid of those primary cats
-
03-04-2013, 01:04 PM #10
-
03-04-2013, 01:33 PM #11
Member
- Join Date
- Feb 2011
- Posts
- 982
- Rep Points
- 1,552.0
- Mentioned
- 19 Post(s)
- Rep Power
- 16
2002 E46 M3 6MT | Jet Black . Black Nappa | My GermanBoost Build Thread
2009 E90 M3 DCT | Melbourne Red . Speed Cloth
-
03-04-2013, 01:53 PM #12
so i'm guessing from the videos i saw , the ESS M3 and Weistec stage 2 C63 are similarly matched
TIME TO MOVE ON !
-
03-04-2013, 02:01 PM #13
Member
- Join Date
- Feb 2013
- Posts
- 16
- Rep Points
- 83.6
- Mentioned
- 5 Post(s)
- Rep Power
- 0
They had one run and the Weistec pulled a bit on the M3, but it did get the jump. I'd say they are pretty close.
-
03-04-2013, 04:36 PM #14
-
03-05-2013, 10:16 PM #15
Timeout
- Join Date
- Feb 2010
- Location
- NJ
- Posts
- 13,412
- Rep Points
- 58.0
- Mentioned
- 318 Post(s)
- Rep Power
- 0
-
03-06-2013, 01:07 PM #16
-
05-27-2013, 09:02 PM #17
Timeout
- Join Date
- Feb 2010
- Location
- NJ
- Posts
- 13,412
- Rep Points
- 58.0
- Mentioned
- 318 Post(s)
- Rep Power
- 0
Welcome to a...
Killakuer654 is now here!